RATED: 2 for Difficulty
This piece was perhaps the easiest I have done so far, but it also took many small steps and time. In the end I think its pretty adorable, but I'm concerned it is a bit fragile and the second its stepped on or given too much pressure it will break - so I'd recommend it for an older child's dollhouse.
 |
| Carve the top center of the heart (or your shape). |
3 Wooden Cut Outs
~2 for the "legs" (Same size)
~1 for the table top
Wood Glue
A straight edged knife
A "V" edged knife (Optional)
Sand Paper
Paint
 |
| Carve the bottom center of the heart (or your shape). |
The wood I chose is very slim, maybe 1/4 inch thick.
Start by carving a slim straight line in the top of one heart and on the base of the other.
These take a bit of time because if you make the cuts too wide they will fall apart.
 |
| Widen it with the "V" Tool. |
I forced mine once I got most of it done and it worked pretty well, it was a tight squeeze but its nice and sturdy now.
I found my "V" tool was best to use to take out the material quickly once I etched it with my line blade. It was also nice to take away some rough edges once I had the piece near the right thickness of the wood.
 |
| Get the fit snug and make sure it stands nice and flat. |
Next test the fit, I slid them together several times to find the snug fit, its important to make sure the legs are level or the table will wobble. When you get close simply sand down a bit and wedge the pieces together. I found I could apply quite a bit of pressure to these little pieces and in the end they fit pretty snugly.
Sand it smooth, and glue it together as much as you want.
Next paint. I have already created the patchwork quilt, and knew I wanted the room to be in the soft blues and mauve-pinks, so choosing the color was pretty simple. Since my paints didn't match perfectly I ended up mixing.
If you have never mixed your own paint it can be quite a challenge, and making sure you make enough so you don't have to start over can be just as frustrating. We all know the basics, red and blue make purple, blue and yellow make green, yellow and red make orange. But adding bits of white, gray, black, or even brown can add warmth or a tint you didn't know was possible.
When I start mixing my acrylics I settle down for the "Long haul" unless you have some way of keeping them moist with retardants, humidity, or wet paint boxes your paints will dry out if you haven't got your projects ready to paint before hand.
Which means have your wood sanded and prepped, clean it with a damp paper-towel and make sure its nice and dry.
Then if I have a specific color in mind (In this case matching it to the mauve color on the quilt.) I would look and decide what colors probably made it up. In this case I knew there was a red closer to the purple scale than the orange. I also knew the gray around it complimented it, so I guessed it was mixed a very light gray blue gray instead of pure white.
So I took my colors and using a paper plate simply squirted three separate piles of paint around the edges of it. Why didn't I just pool it all together in the central part of the plate you ask? I had no clue how much of what color I needed, and putting separate piles allow for you to mix and match without reopening the tubes or having to scrap it entirely and start over. Then I took a plastic knife (If you have a paint blade awesome, but a plastic knife works.) and I took a big chunk of my red and some of my gray and white and started in the mix.
Adding small portions I built up until I was pretty close to the color I wanted. I made sure to use a bit more than I thought I would need to use because I wasn't priming my table and it would soak up more of the paint then if I was or if I was painting on a prepped canvas. Also with acrylics when they dry they tend to dry lighter than when wet, so keep that in mind when mixing.
The other fun with acrylics is you can use them as a paint, as a wash (or glaze), or as a water-color simply by adding more water. Since the wood on these wasn't particularly "grained" I chose to use it as a paint and while I was careful to do it smoothly with enough water that it wasn't really bubbled anywhere, it looks thick like a paint instead of as a wash. (More on that in the bed-making tutorial.)
You want to make sure its fully dry before you work with it again or you will get fingerprints on it. I usually wait over night.
Once dry flatten the top by filing (I used a rip-file my husband informed me) to take the tip of the hearts off making it flat enough for the table top to fit on top of. (See the photo above.) If you look closely at the top you will see where my wood flaked a bit due to the rugged file. If you paint after this you can prevent that, but it was barely noticeable when creating and once glued its completely not. But I'm telling you what I learned (haha).
Glue the top to the base. Clamp it - or it will most likely dry crooked - mine partially did and I had to add more and adjust it.
Once finished you can embellish it however you'd like. I am still debating on adding a few hearts to the legs.
In the end this is my little table, about three inches tall with a nice flat table top that can hold teddies or lamps or clocks or whatever knickknacks you want to finish your room with.
Next paint. I have already created the patchwork quilt, and knew I wanted the room to be in the soft blues and mauve-pinks, so choosing the color was pretty simple. Since my paints didn't match perfectly I ended up mixing.
If you have never mixed your own paint it can be quite a challenge, and making sure you make enough so you don't have to start over can be just as frustrating. We all know the basics, red and blue make purple, blue and yellow make green, yellow and red make orange. But adding bits of white, gray, black, or even brown can add warmth or a tint you didn't know was possible.
 |
| My mauve color inspiration. |
Which means have your wood sanded and prepped, clean it with a damp paper-towel and make sure its nice and dry.
Then if I have a specific color in mind (In this case matching it to the mauve color on the quilt.) I would look and decide what colors probably made it up. In this case I knew there was a red closer to the purple scale than the orange. I also knew the gray around it complimented it, so I guessed it was mixed a very light gray blue gray instead of pure white.
 |
| Pretty fair match on color I think. |
Adding small portions I built up until I was pretty close to the color I wanted. I made sure to use a bit more than I thought I would need to use because I wasn't priming my table and it would soak up more of the paint then if I was or if I was painting on a prepped canvas. Also with acrylics when they dry they tend to dry lighter than when wet, so keep that in mind when mixing.
 |
| File the tip down to be flat to hold the table top. |
You want to make sure its fully dry before you work with it again or you will get fingerprints on it. I usually wait over night.
Once dry flatten the top by filing (I used a rip-file my husband informed me) to take the tip of the hearts off making it flat enough for the table top to fit on top of. (See the photo above.) If you look closely at the top you will see where my wood flaked a bit due to the rugged file. If you paint after this you can prevent that, but it was barely noticeable when creating and once glued its completely not. But I'm telling you what I learned (haha).
Glue the top to the base. Clamp it - or it will most likely dry crooked - mine partially did and I had to add more and adjust it.
Once finished you can embellish it however you'd like. I am still debating on adding a few hearts to the legs.
In the end this is my little table, about three inches tall with a nice flat table top that can hold teddies or lamps or clocks or whatever knickknacks you want to finish your room with.
 |
| The finished piece. |
***You could easily adjust this piece by buying wooden flowers, stars, trees, circles, squares etc to better fit the decor of your dollhouse's room.***
No comments:
Post a Comment